Run a Command on an SSH Session Channel

See more SSH Examples

Demonstrates the Chilkat Ssh.SendReqExec method, which requests execution of a command on a session channel. The first argument is the channel number and the second is the command line. This example runs a command, reads the output until the channel closes, and prints it.

-- Important: See this note about string length limitations for strings returned by sp_OAMethod calls.
--
CREATE PROCEDURE ChilkatSample
AS
BEGIN
    DECLARE @hr int
    DECLARE @iTmp0 int
    DECLARE @sTmp0 nvarchar(4000)
    DECLARE @success int
    SELECT @success = 0

    --  Demonstrates the Ssh.SendReqExec method, which requests execution of a command on a session
    --  channel.  The 1st argument is the channel number and the 2nd is the command line.

    DECLARE @ssh int
    EXEC @hr = sp_OACreate 'Chilkat.Ssh', @ssh OUT
    IF @hr <> 0
    BEGIN
        PRINT 'Failed to create ActiveX component'
        RETURN
    END

    DECLARE @sshPort int
    SELECT @sshPort = 22
    EXEC sp_OAMethod @ssh, 'Connect', @success OUT, 'ssh.example.com', @sshPort
    IF @success = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    --  Normally you would not hard-code the password in source.  You should instead obtain it
    --  from an interactive prompt, environment variable, or a secrets vault.
    DECLARE @password nvarchar(4000)
    SELECT @password = 'mySshPassword'

    EXEC sp_OAMethod @ssh, 'AuthenticatePw', @success OUT, 'mySshLogin', @password
    IF @success = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    --  Open a session channel.  A negative return value indicates failure.
    DECLARE @channelNum int
    EXEC sp_OAMethod @ssh, 'OpenSessionChannel', @channelNum OUT
    IF @channelNum < 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    --  Request execution of a command.  A 1 return means the server accepted the request; it
    --  does not mean the command itself succeeded.
    EXEC sp_OAMethod @ssh, 'SendReqExec', @success OUT, @channelNum, 'ls -l /tmp'
    IF @success = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    --  IMPORTANT: Set a read timeout.  ReadTimeoutMs defaults to 0, which means no limit -- without
    --  it, this call waits forever if the server never sends channel close.
    EXEC sp_OASetProperty @ssh, 'ReadTimeoutMs', 15000

    --  Read the command output until the server closes the channel.
    EXEC sp_OAMethod @ssh, 'ChannelReceiveToClose', @success OUT, @channelNum
    IF @success = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    DECLARE @output nvarchar(4000)
    EXEC sp_OAMethod @ssh, 'GetReceivedText', @output OUT, @channelNum, 'utf-8'
    EXEC sp_OAGetProperty @ssh, 'LastMethodSuccess', @iTmp0 OUT
    IF @iTmp0 = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    PRINT @output

    EXEC sp_OAMethod @ssh, 'Disconnect', NULL

    EXEC @hr = sp_OADestroy @ssh


END
GO