Check Whether SSH Channel CLOSE Was Received

See more SSH Examples

Demonstrates the Chilkat Ssh.ChannelReceivedClose method, which reports whether an SSH CLOSE message has been received for a channel. The only argument is the channel number. Remote CLOSE is distinct from EOF and closes the channel in both directions.

-- Important: See this note about string length limitations for strings returned by sp_OAMethod calls.
--
CREATE PROCEDURE ChilkatSample
AS
BEGIN
    DECLARE @hr int
    DECLARE @iTmp0 int
    DECLARE @sTmp0 nvarchar(4000)
    DECLARE @success int
    SELECT @success = 0

    --  Demonstrates the Ssh.ChannelReceivedClose method, which reports whether an SSH CLOSE message
    --  has been received for a channel.  The only argument is the channel number.  Remote CLOSE is
    --  distinct from EOF and closes the channel in both directions.

    DECLARE @ssh int
    EXEC @hr = sp_OACreate 'Chilkat.Ssh', @ssh OUT
    IF @hr <> 0
    BEGIN
        PRINT 'Failed to create ActiveX component'
        RETURN
    END

    DECLARE @sshPort int
    SELECT @sshPort = 22
    EXEC sp_OAMethod @ssh, 'Connect', @success OUT, 'ssh.example.com', @sshPort
    IF @success = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    --  Normally you would not hard-code the password in source.  You should instead obtain it
    --  from an interactive prompt, environment variable, or a secrets vault.
    DECLARE @password nvarchar(4000)
    SELECT @password = 'mySshPassword'

    EXEC sp_OAMethod @ssh, 'AuthenticatePw', @success OUT, 'mySshLogin', @password
    IF @success = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    DECLARE @channelNum int
    EXEC sp_OAMethod @ssh, 'OpenSessionChannel', @channelNum OUT
    IF @channelNum < 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    EXEC sp_OAMethod @ssh, 'SendReqExec', @success OUT, @channelNum, 'ls -l /tmp'
    IF @success = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    --  IMPORTANT: Set a read timeout.  ReadTimeoutMs defaults to 0, which means no limit -- without
    --  it, this call waits forever if the server never sends channel close.
    EXEC sp_OASetProperty @ssh, 'ReadTimeoutMs', 15000

    EXEC sp_OAMethod @ssh, 'ChannelReceiveToClose', @success OUT, @channelNum
    IF @success = 0
      BEGIN
        EXEC sp_OAGetProperty @ssh, 'LastErrorText', @sTmp0 OUT
        PRINT @sTmp0
        EXEC @hr = sp_OADestroy @ssh
        RETURN
      END

    --  The server may send EOF before CLOSE.  During that interval EOF is 1 while CLOSE is
    --  still 0.
    EXEC sp_OAMethod @ssh, 'ChannelReceivedEof', @iTmp0 OUT, @channelNum
    IF @iTmp0
      BEGIN

        PRINT 'EOF received.'
      END

    EXEC sp_OAMethod @ssh, 'ChannelReceivedClose', @iTmp0 OUT, @channelNum
    IF @iTmp0
      BEGIN

        PRINT 'Remote CLOSE received -- the channel is closed in both directions.'
      END
    ELSE
      BEGIN

        PRINT 'No remote CLOSE received.'
      END

    EXEC sp_OAMethod @ssh, 'Disconnect', NULL

    EXEC @hr = sp_OADestroy @ssh


END
GO